Heating, cooling, and the air in between.
Every HVAC service Falls to Falls offers, organized the way an honest tech thinks about a house: what keeps you warm, what keeps you cool, and what the air quality looks like in between.
When the temperature drops, we’re the first call.
Eastern Idaho winters don’t forgive a failing furnace. Twelve heating services covering everything from emergency repair to new-construction installs.
Same-day diagnostic + repair on gas, electric, and oil furnaces. Most failures resolved on the first visit.
→Annual tune-up + safety inspection + combustion analysis. Catches problems while they’re cheap.
→Hot-water boiler repair — circulators, zone valves, expansion tanks, controls, aquastats.
→Annual boiler service — flush, combustion analysis, safeties, burner clean.
→Heat pumps in defrost loop, short-cycling, or running auxiliary heat constantly. Diagnose first.
→Baseboard, wall-mount, electric resistance — whatever you call your heater, we fix.
→Full system install — Manual-J sized, sealed ductwork, permitted electrical.
→When the math says new beats repair, we replace — right-sized + efficiency-matched.
→24/7 emergency response. Flat after-hours rate, no escalating dispatch fees.
→Light-commercial chiller annual service + emergency repair on air-cooled units.
→New-build furnace installs sized to the actual load — not the cheapest equivalent.
→Commissioning + warranty repair on new-build furnaces, usually a configuration issue.
→When summer hits, we keep your home livable.
AC failures spike on the first 95-degree week of the year. Eleven cooling services from residential AC repair to commercial rooftop unit service.
Same-day diagnostic + repair. Most common failures — compressor, refrigerant, control board — resolved on first visit.
→Mini-split head, condenser, refrigerant, and inverter-board repair on all major brands.
→Blower motor, evaporator coil, capacitor, control-board repair — isolate to the failed part.
→EPA-certified recharge for R-410A, R-22 retrofits, and newer A2L systems. Find the leak first.
→Retrofits + full flush for R-22 legacy systems and newer EPA-regulated refrigerants.
→Spring AC + fall heat tune-ups. A $150 service catches the $500 surprise.
→AC + air-handler installs on new builds. Manual-J sized, code-compliant ductwork.
→VRF design + install for multi-zone commercial and large-home zoning applications.
→Commercial RTU service — economizers, condenser fans, scroll compressors, gas-valve controls.
→Commercial installs with permits pulled and engineering specs respected. No value-engineered shortcuts.
→Same-day commercial response. Diagnostic, parts, repair, documented — done.
→Everything else that keeps your system honest.
Thirteen services covering the components most contractors skip — indoor air quality, humidification, dehumidification, water heaters, smart controls.
Measure first — particulates, VOCs, CO, humidity, formaldehyde. Then recommend.
→UV, HEPA, MERV upgrades, fresh-air ventilation — targeted to what we measured.
→Whole-house humidifier — bypass, fan-powered, or steam.
→Solenoid, water panel, control-board repair on whole-house humidifiers.
→Whole-house and basement dehum install + service + repair.
→Media + electrostatic + HEPA bypass filtration sized for your system.
→UV-C, bipolar ionization, photocatalytic systems for biological + gaseous loads.
→Tank, tankless, hybrid heat-pump — element, thermostat, controls.
→Sized to actual peak demand + code-compliant venting + permit pulled.
→Install + configuration with proper C-wire pulled, equipment-specific staging.
→Whole-system efficiency upgrades that actually move your utility bill.
→Scheduled maintenance + priority response + remote system monitoring.
→New-build water heater spec done right — not value-engineered to fail.
→Not sure which service you need?
Describe what’s happening — Larry will tell you what to do next. Free, no obligation, no sales pitch.
